Projecte llegit
Títol: Aerodynamic assessment of Open Fan Architecture
Estudiants que han llegit aquest projecte:
EXTREMERA MAZÓN, GERARD (data lectura: 30-10-2026)- Cerca aquest projecte a Bibliotècnica
EXTREMERA MAZÓN, GERARD (data lectura: 30-10-2026)Director/a: ALTMEYER, SEBASTIÁN ANDREAS
Departament: FIS
Títol: Aerodynamic assessment of Open Fan Architecture
Data inici oferta: 08-12-2025 Data finalització oferta: 08-07-2026
Estudis d'assignació del projecte:
GR ENG SIS TELECOMUN
GR ENG SIST AEROESP
GR ENG TELEMÀTICA
| Tipus: Individual | |
| Lloc de realització: EETAC | |
| Paraules clau: | |
| Computational fluid dynamics, open-fan design, propeller design, rotor-stator configuration, CFM RISE | |
| Descripció del contingut i pla d'activitats: | |
| This project presents a study of the open fan architecture, combining conceptual analysis, blade design and computational fluid dynamics simulation. The main objective is to develop and evaluate rotor and stator blade geometries that can improve propulsive efficiency while respecting realistic constraints.
The work begins with a state-of-the-art review of current open-fan developments, paying special attention to the principles and performance of the CFM RISE concept. This review helps define the performance indicators, geometries and operating conditions that will guide the design phase. A brief overview of earlier contra-rotating concepts is also included to justify the selection of a rotor-stator configuration for this study. A parametric blade design will be created in SolidWorks, allowing controlled variation of key geometric features such as chord, pitch, twist, camber, number of blades and rotor-stator spacing. These blade sets will be integrated around a simplified engine-core geometry to realistically represent the open-fan module. The resulting geometries will be studied using ANSYS Fluent. Simulations will be conducted to analyse rotor-stator interaction, swirl development and wake evolution. If feasible, a simplified aeroacoustic estimation will also be conducted. The expected outcome is a validated aerodynamic assessment of the open fan concept, identifying promising blade designs and offering guidance for future improvements and more advanced studies. |
|
| Overview (resum en anglès): | |
| Open fans remove the nacelle of the turbofan to reach a higher propulsive efficiency, but they expose the blade tips to a supersonic relative flow and, with a single rotor, leave in the wake the swirl that a stator would recover. This thesis presents the aerodynamic design and CFD verification of a single-rotation open fan rotor for an A320-class aircraft in cruise at Mach 0.78 and 11 900 m. The rotor has a diameter of 4 m, 14 blades and a shaft speed of 1 100 rpm, which gives a helical tip Mach number of 1.10.
The design followed three phases. In the first, the blade came directly from the lifting-line code XROTOR with a swept and leaned stacking line, and the CFD showed that its outer half was almost unloaded, because XROTOR sets the twist with the helical Mach number while the swept sections work at a much lower one. In the second, a compressibility re-twist evaluated in the normal plane of each section raised the efficiency of the same blade by 0.161, and a band-by-band analysis of the CFD pointed to the blockage of the blade-to-blade passage at the root as the remaining limitation. In the third, an empirical three-dimensional correction model calibrated on the CFD of the earlier blades and a two-stage optimiser, chord law first and stacking line second, produced the final blade. It thins the root to 10 % thickness and sweeps the stacking line up to 41 degrees at the tip, limited by stall at a single station. Seven blades were evaluated with steady RANS simulations on a periodic sector. In a second-order solution the final blade produces 21 795 N, above its 20 kN design thrust, with a rotor efficiency of 72.6 %, and the correction model predicted its thrust within 2.1 % of the first-order CFD before it was run. The measured power balance shows that 11.7 % of the shaft power leaves the rotor as swirl. Against NASA's N-OPEN-1 rotor, which reaches an efficiency of 71.0 % with the same turbulence model, the rotor designed in this work achieves a slightly higher efficiency with a supersonic tip and a 65 % higher disc loading. A stator recovering the swirl at the rate measured on N-OPEN-1 would bring the stage to an estimated 80.8 %. Finally, a cycle analysis places the rotor in an engine with the same core technology as a CFM56-class turbofan: the open fan reaches a bypass ratio close to 50, its core exhaust adds 1.7 kN so that rotor and core exceed the 22 337 N requirement, and its cruise TSFC is 9.3 % lower with the rotor alone and about 18 % lower with a stator. |
|