Projecte llegit
Títol: Aerodynamic Analysis of a NACA 0015 Circulation Control Airfoil using CFD at Low Reynolds Number
Estudiants que han llegit aquest projecte:
GUIRAO SÁNCHEZ, JOEL (data lectura: 27-10-2026)- Cerca aquest projecte a Bibliotècnica
GUIRAO SÁNCHEZ, JOEL (data lectura: 27-10-2026)Director/a: ALTMEYER, SEBASTIÁN ANDREAS
Departament: FIS
Títol: Aerodynamic Analysis of a NACA 0015 Circulation Control Airfoil using CFD at Low Reynolds Number
Data inici oferta: 26-01-2026 Data finalització oferta: 26-09-2026
Estudis d'assignació del projecte:
GR ENG SIS TELECOMUN
GR ENG SIST AEROESP
GR ENG TELEMÀTICA
| Tipus: Individual | |
| Lloc de realització: EETAC | |
| Paraules clau: | |
| NACA 0015, circulation control, active flow control, Coand¿ effect, low Reynolds number, CFD, Ansys Fluent, SST k-¿, laminar separation bubble, boundary layer, trailing edge, continuous blowing jet, UAV, aerodynamic efficiency. | |
| Descripció del contingut i pla d'activitats: | |
| This project presents a theoretical and computational study of active flow control using synthetic jet actuators applied to unmanned aerial vehicles (UAVs). The main objective is to analyse the effect of wingtip vortices and delta wing structure in UAVs performance. The key object of the project is to show through the study in which chord configuration the synthetic jet produces greater aerodynamic efficiency. Pre and Post processing stage would include the generation of a complete airfoil design with
built-in sweeping jets. It requires parametric inputs like altering the position of jets in order to calculate the induced drag and thus decrease the drag effects. The UAVs design will be created with SolidWorks, where the airflow will be studied in ANSYS Fluent, analyzing components such as flow separation, velocity and pressure fields, and aerodynamic coefficients such as lift and drag. The expected result is a quantitative validation of the effectiveness of synthetic jet actuators for active flow control, contributing to the identification of optimal configurations and the possible improvement of aerodynamic performance. |
|
| Overview (resum en anglès): | |
| The steady growth of unmanned aerial vehicles has favoured fixed-wing configurations, whose range and efficiency exceed those of multirotor platforms. Their operation at low Reynolds numbers is penalised by viscous effects: the boundary layer separates prematurely and the loss of lift limits the flight envelope. Active flow control offers a way to address this, and continuous blowing jets stand out because they adapt the wing aerodynamics dynamically, unlike passive devices such as vortex generators. Previous work on blowing jets has concentrated on delta wings at subsonic and transonic speeds, where compressibility dominates, so their effect on airfoils in the incompressible low-Reynolds regime typical of UAVs remains far less explored. This thesis addresses that gap with a numerical study of a modified NACA 0015 airfoil with a Coanda surface at the trailing edge, a circulation control configuration. The geometry and conditions reproduce the wind tunnel experiments of Itsariyapinyo and Sharma, with a chord of 170 mm, a free-stream velocity of 10 m/s, incompressible air and a chord-based Reynolds number of 1.10e5.
The work was carried out in Ansys Fluent with a pressure-based, steady-state solver and the SST k-omega turbulence model, integrating the equations down to the wall. The domain is a single continuous fluid body with a body of influence around the airfoil and symmetry conditions on the lateral walls, so that no boundary layer develops on them. Inflation layers keep y+ below unity on both surfaces. The mesh independence study, with meshes from 2.6 to 10.1 million elements, showed drag variations of about 0.3 % between the two densest meshes, and 3.5 million elements were chosen as a compromise with the 8 GB of RAM available. The results comprise the pressure coefficient along the chord from 0 to 15 degrees, contoured fields in the mid-span plane and the aerodynamic coefficients. The pressure distributions match the experimental shape up to about 9 degrees, but from there the numerical suction peak weakens and at 15 degrees the flow stays attached where the experiment shows the flattened distribution of separated flow. The computed lift is 45 to 55 % lower and the drag 170 to 390 % higher, giving an efficiency 80 to 90 % lower. The blowing slots, 0.2 mm high against a chord of 0.17 m, were not included: meshing them would multiply the cell count out of proportion to their size. Their inclusion, a finer mesh at the trailing edge and wake, a transition model to capture the laminar separation bubble and a transient simulation of the jets are proposed as future work, since the baseline obtained here is the reference against which active flow control must be measured. |
|