CBL - Campus del Baix Llobregat

Projecte llegit

Títol: Domòtica sense núvol: disseny, desplegament i validació d'una llar intel·ligent local


Estudiants que han llegit aquest projecte:


Director/a: ALONSO ZÁRATE, LUIS

Departament: TSC

Títol: Domòtica sense núvol: disseny, desplegament i validació d'una llar intel·ligent local

Data inici oferta: 02-02-2026     Data finalització oferta: 02-10-2026



Estudis d'assignació del projecte:
    GR ENG SIS TELECOMUN
Tipus: Individual
 
Lloc de realització: EETAC
 
Paraules clau:
IoT, wireless communications, comunicacions sense fils, domòtica
 
Descripció del contingut i pla d'activitats:
L'objectiu principal del TFG és dissenyar i implementar una arquitectura domòtica IoT funcional per a una llar real, analitzant les comunicacions i el comportament del sistema.
Les tasques principals que es faran són: Definir una arquitectura per capes del sistema, integrar dispositius IoT mitjançant diferents tecnologies de comunicació, implementar automatitzacions de processos, analitzar paràmetres de rendiment de la xarxa completa i estimar els costos d'implementació i operació.
Aquest TFG no només consisteix a construir un prototip de llar domòtica, sinó també a analitzar críticament el sistema desenvolupat. Això inclou una avaluació tècnica de com funciona la instal·lació: fiabilitat de la comunicació, automatització dels processos, integració de dispositius i la robustesa global del sistema.
A més, s'analitzarà de manera realista el sistema: el temps necessari per implementar-lo, la complexitat que implica, i si caldria l'assistència d'un expert per desplegar-lo correctament. Aquest enfocament permet valorar si el projecte és viable i quins punts caldria millorar abans d'una implementació a gran escala.
 
Overview (resum en anglès):
Most consumer home automation devices depend on the manufacturer's servers, so household data leaves the home, every command must make a round trip to a remote server, and service continuity is subject to third-party decisions. Open-source platforms allow all the logic to run at home, but quantitative characterisations of their behaviour are scarce. This project designs, deploys and validates a locally executed home automation system in a real dwelling, and measures its performance.

The system is built around a single node, a Raspberry Pi 5 running Home Assistant, which integrates fifteen commercial devices using three radio technologies: twelve Zigbee devices through Zigbee2MQTT and an MQTT broker, two Wi-Fi plugs via the Matter standard, and a lighting controller over Bluetooth Low Energy. On this basis, nineteen automations have been implemented, written against entities rather than specific technologies, to meet the real needs of the household.

Validation relies on telemetry obtained from the system itself. The latency of four control chains was characterised over 2,077 valid measurements: medians range from 41 to 121 ms, 95th percentiles stay below 180 ms, and only 0.6% of the measurements exceed half a second. In order of magnitude, these values are between two and seven times lower than those published for a cloud-mediated installation. Reception quality in the Zigbee mesh is high and stable, with a median LQI of 184 out of 255 over 148,632 measurements, and the node runs at 1% of its computing capacity. A loss-of-connectivity test shows that the Zigbee devices keep full functionality, whereas the Matter actuator becomes unreachable: Matter provides local control but not network autonomy.

The sustainability study concludes that the system consumes between five and thirteen times the energy it can save at most, and that it has no payback horizon. Its value lies not in energy efficiency, but in response time, local control, independence from manufacturers and data privacy.


© CBLTIC Campus del Baix Llobregat - UPC